CISCO ASA 5505 经典配置案例

nterface Vlan2
 nameif outside  ----------------------------------------对端口命名外端口 
 security-level 0 ----------------------------------------设置端口等级
 ip address X.X.X.X 255.255.255.224       --------------------调试外网地址
!
interface Vlan3
 nameif inside    ----------------------------------------对端口命名内端口  
 security-level 100  ----------------------------------------调试外网地址
 ip address 192.168.1.1 255.255.255.0     --------------------设置端口等级
!
interface Ethernet0/0
 switchport access vlan 2   ----------------------------------------设置端口VLAN与VLAN2绑定
!
interface Ethernet0/1
 switchport access vlan 3  ----------------------------------------设置端口VLAN与VLAN3绑定
!
interface Ethernet0/2
 shutdown
!
interface Ethernet0/3
 shutdown
!
interface Ethernet0/4
 shutdown
!
interface Ethernet0/5
 shutdown
!
interface Ethernet0/6
 shutdown
!
interface Ethernet0/7
 shutdown
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
 name-server 211.99.129.210
 name-server 202.106.196.115
access-list 102 extended permit icmp any any          ------------------设置ACL列表（允许ICMP全部通过）
access-list 102 extended permit ip any any            ------------------设置ACL列表（允许所有IP全部通过）
pager lines 24
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface  ----------------------------------------设置NAT地址映射到外网口
nat (inside) 1 0.0.0.0 0.0.0.0  0---------------------------------NAT地址池（所有地址）0无最大会话数限制
access-group 102 in interface outside          ------------------―――设置ACL列表绑定到外端口
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1        ------------------设置到外网的默认路由
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet 0.0.0.0 0.0.0.0 inside ----------------------------------------设置TELNET所有地址进入
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside   ----------------------------------------设置SSH所有地址进入
ssh timeout 30
ssh version 2
console timeout 0        
!
dhcpd address 192.168.1.100-192.168.1.199 inside               ------------------设置DHCP服务器地址池
dhcpd dns 211.99.129.210 202.106.196.115 interface inside  ------------------设置DNS服务器到内网端口
dhcpd enable inside   --------------------------------------------------------------设置DHCP应用到内网端口
!

前几天去客户那调试CISCO-ASA-5505设备,第一次摸,跟PIX一样,呵呵.没有技术含量,都是最基本的.其他业务配置暂时没配,会及时更新的.

Cisco ASA5505配置
cisco, config, telnet, 防火墙, Cisco
1.配置防火墙名
ciscoasa> enable
ciscoasa# configure terminal
ciscoasa(config)# hostname asa5505
2.配置telnet
asa5505(config)#telnet 192.168.1.0 255.255.255.0 inside ↑//允许内部接口192.168.1.0网段telnet防火墙
3.配置密码
asa5505(config)# password cisco ------------------远程密码
asa5505(config)# enable password cisco ------------------特权模式密码
4.配置IP
asa5505(config)# interface vlan 2 ------------------进入vlan2
asa5505(config-if)# ip address 218.16.37.222 255.255.255.192 ------------------vlan2配置IP
asa5505(config)#show ip address vlan2 ------------------验证配置
5.端口加入vlan
asa5505(config)# interface e0/3 ------------------进入接口e0/3
asa5505(config-if)# switchport access vlan 3 ------------------接口e0/3加入vlan3
asa5505(config)# interface vlan 3 ------------------进入vlan3
asa5505(config-if)# ip address 10.10.10.36 255.255.255.224 ------------------vlan3配置IP
asa5505(config-if)# nameif dmz ------------------vlan3名
asa5505(config-if)# no shutdown ------------------开启
asa5505(config-if)# show switch vlan ------------------验证配置
6.最大传输单元MTU
asa5505(config)#mtu inside 1500 ------------------inside最大传输单元1500字节
asa5505(config)#mtu outside 1500 ------------------outside最大传输单元1500字节
asa5505(config)#mtu dmz 1500 ------------------dmz最大传输单元1500字节
7.配置arp表的超时时间
asa5505(config)#arp timeout 14400 ------------------arp表的超时时间14400秒
8.FTP模式
asa5505(config)#ftp mode passive ------------------FTP被动模式
9.配置域名
asa5505(config)#domain-name Cisco.com
10.启动日志
asa5505(config)#logging enable ------------------启动日志
asa5505(config)#logging asdm informational ------------------启动asdm报告日志
asa5505(config)#Show logging ------------------验证配置
11.启用http服务
asa5505(config)#http server enable   ------------------启动HTTP server,便于ASDM连接。
asa5505(config)#http 0.0.0.0 0.0.0.0 outside ------------------对外启用ASDM连接
asa5505(config)#http 0.0.0.0 0.0.0.0 inside  ------------------对内启用ASDM连接
12.控制列表
access-list acl_out extended permit tcp any any eq www ------------------允许tcp协议80端口入站
access-list acl_out extended permit tcp any any eq https ------------------允许tcp协议443端口入站
access-list acl_out extended permit tcp any host 218.16.37.223 eq ftp
↑//允许tcp协议21端口到218.16.37.223主机
access-list acl_out extended permit tcp any host 218.16.37.224 eq 3389
↑//允许tcp协议3389端口到218.16.37.224主机
access-list acl_out extended permit tcp any host 218.16.37.225 eq 1433
↑//允许tcp协议1433端口到218.16.37.225主机
access-list acl_out extended permit tcp any host 218.16.37.226 eq 8080
↑//允许tcp协议8080端口到218.16.37.226主机
asa5505(config)#show access-list ------------------验证配置
13.设置路由
asa5505(config)#route dmz 10.0.0.0 255.0.0.0 10.10.10.33  1
↑//静态路由到10.0.0.0网段经过10.10.10.33网关跳数为1
asa5505(config)#route outside 0.0.0.0 0.0.0.0 218.16.37.193  1
↑//默认路由到所有网段经过218.16.37.193网关跳数为1
asa5505# show route ------------------显示路由信息
14.静态NAT
asa5505(config)# static (inside,outside) 218.16.37.223 192.168.1.6 netmask 255.255.255.255
↑//外网218.16.37.223映射到内网192.168.1.6
asa5505(config)#access-list acl_out extended permit icmp any any
↑//控制列表名acl_out允许ICMP协议
asa5505(config)#access-group acl_out in interface outside
↑//控制列表acl_out应用到outside接口
asa5505(config)#static (inside,dmz) 10.10.10.37 192.168.1.16      netmask 255.255.255.255
↑//dmz10.10.10.37映射到内网192.168.1.16
asa5505(config)#access-list acl_dmz extended permit icmp any any
↑//控制列表名acl_dmz允许ICMP协议
asa5505(config)#access-group acl_dmz in interface dmz -----------------控制列表acl_out应用到dmz接口 asa5505(config)#Show nat ------------------验证配置
15.动态NAT
asa5505(config)#global(outside)  1  218.201.35.224-218.201.35.226 ------------------定义全局地址池
asa5505(config)#nat(inside)  1  192.168.1.20-192.168.1.22 ------------------内部转换地址池
asa5505(config)# show xlate ------------------验证配置
16.基于端口NAT（PAT）
asa5505(config)#global (outside)  2  interface ----------------定义全局地址即outside地址：218.16.37.222
asa5505(config)#nat (inside)  2  192.168.1.0 255.255.255.0 ------------------内部转换地址池
asa5505(config)# show xlate ------------------验证配置
17.基于LAN故障倒换（failover）
1).主防火墙配置
asa5505(config)#failover mac addr outside 001a.2b3c.4d11 001a.2b3c.4w12----故障倒换虚拟MAC地址
asa5505(config)#failover mac addr inside 001a.2b3c.4d21 001a.2b3c.4w22-----故障倒换虚拟MAC地址
asa5505(config)#failover mac addr inside 001a.2b3c.4d21 001a.2b3c.4w32-----故障倒换虚拟MAC地址
asa5505(config)#failover ------------------启动故障倒换
asa5505(config)#failover lan unit primary ------------------设置主要防火墙
asa5505(config)#failover lan interface standby Vlan4 ------------------故障倒换接口名standby
asa5505(config)#failover interface ip standby 172.168.32.1 255.255.255.252 standby 172.168.32.2
↑//配置主防火墙IP：172.168.32.1,备用防火墙IP：172.168.32.2
asa5505# show failover ------------------验证配置
2).备防火墙配置
asa5505(config)#failover mac addr outside 001a.2b3c.4d11 001a.2b3c.4w12----故障倒换虚拟MAC地址
asa5505(config)#failover mac addr inside 001a.2b3c.4d21 001a.2b3c.4w22------故障倒换虚拟MAC地址asa5505(config)#failover mac addr inside 001a.2b3c.4d21 001a.2b3c.4w32------故障倒换虚拟MAC地址asa5505(config)#failover ------------------启动故障倒换
asa5505(config)#failover lan unit secondary ------------------设置备用防火墙
asa5505(config)#failover lan interface standby Vlan4 ------------------故障倒换接口名standby
asa5505(config)#failover interface ip standby 172.168.32.1 255.255.255.252 standby 172.168.32.2
↑//配置主防火墙IP：172.168.32.1,备用防火墙IP：172.168.32.2
asa5505# show failover ------------------验证配置
18.显示mac地址
asa5505# show switch mac-address-table
19.保存配置
asa5505# write memory

Cisco ASA 5505防火墙地址映射问题

解决前些天帮朋友配置一台Cisco ASA5505防火墙, 映射总是不成功. 在网上也看到很多朋友遇到了这种问题,都在寻问这个解决方法.有人已经将问题解决了,但没给出解决方案.   也许这并不是一个很复杂的难题,但我希望通过博客能帮助朋友们及时得到这个小问题的处理.
基本情况:  
WAN: 221.221.147.195    Gateway: 221.221.147.200  LAN: 192.168.0.1
内网中有一台服务器,地址: 192.168.0.10    端口: 8089
故障描述:  内网可正常连接至服务器,外网无法连接.   端口映射出现问题.
解决方法:  命令行错误, 已更正并解决.
问题重点:  采用 "static (inside,outside) 221.221.147.195 192.168.0.10 tcp 8089" 映射.
目前配置如下:
ASA Version 7.2(2)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 221.221.147.195 255.255.255.252
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list 101 extended permit tcp any host 221.221.147.195 eq 8089
access-list 101 extended permit icmp any any
access-list 101 extended permit tcp any any
access-list 101 extended permit udp any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
static (inside,outside) 221.221.147.195 192.168.0.10 netmask 255.255.255.255 tcp 8089 0
access-group 101 in interface outside
route outside 0.0.0.0 0.0.0.0 221.221.147.200 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
http server enable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
!
class-map inspection_default
match default-inspection-traffic
!
policy-map type inspect dns preset_dns_map
parameters
  message-length maximum 512
policy-map global_policy
class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny
  inspect sunrpc
  inspect xdmcp
  inspect sip
  inspect netbios
  inspect tftp
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:30e219cbc04a4c919e7411de55e14a64
: end
ciscoasa(config)#
------------------------------------------------------------
在找寻解决方案过程中,有朋友做了重要提示, 采用: static (inside,outside) int 192.168.0.10 tcp 8089 做映射,但出现警告提示:
WARNING: static redireting all traffics at outside interface;
WARNING: all services terminating at outside interface are disabled.
后来将命令改成:  static (inside,outside) 221.221.147.195 192.168.0.10 tcp 8089   问题解决.

ASA5505配置笔记  
                            ASA5505配置笔记
1.IP地址配置
  #int vlan1
  #>nameif outside
  #security-level 0
  #ip address 172.16.1.1 255.255.0.0.
  #end
  #int vlan 2
  #nameif insiede
  #security-levlel 100
  #ip address 192.168.1.1 255.255.255.0
  #end

2.把端口指定到相应VLAN中
#int Eth0/0
#switchport access vlan 1
end
#int Eth0/1
switchport access vlan 2
end
#exit
3.配置Http.telnet和ssh管理
#username xxx password xxxxxx encrypted privilege 15
#aaa authentication enable console LOCAL
#aaa authentication telnet console LOCAL
#aaa authentication http console LOCAL
#aaa authentication ssh console LOCAL
#aaa autoentication command LOCAL
#http server enable
#http 192.168.1.0 255.255.255.0 inside
#telnet 192.168.1.0 255.255.255.0 inside
#ssh 192.168.1.0 255.255.255.0 inside
#crypto key generate rsa(打开SSH服务)
4.VPN配置
  VPN配置可在ASDM模式下配置,具体配置略

CISCO ASA 5510实际配置案例及详解

去年卖个某大型企业的ASA5510防火墙，附实际的配置，并且都解释了得很清楚，非常值得参考的资料！

2008-12-15 11:07
ASA5510# SHOW RUN
: Saved
:
ASA Version 7.0(6)
!
hostname ASA5510
enable password 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
!
interface Ethernet0/0 此接口为外部网络接口
nameif outside 设置为 OUTSIDE 外部接口模式
security-level 0 外部接口模式安全级别为 最高 0
ip address 192.168.3.234 255.255.255.0 添加外部IP地址 （一般为电信÷网通提供）
!

interface Ethernet0/1此接口为内部网络接口
nameif inside设置为 INSIDE
内部接口模式
security-level 100内部接口模式安全级别为 100
ip address 10.1.1.1
255.255.0.0添加内部IP地址 （一般为公司自行分配）
!
interface Ethernet0/2 没用到 SHUTDOWN
关闭
shutdown
no nameif
no security-level
no ip
address
!
interface Management0/0没用到 SHUTDOWN 关闭
nameif
management
security-level 100
ip address 192.168.1.1 255.255.255.0
没用，用网线连接
href="tag.php?name=����">管理的端口。
management-only
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
pager lines 24
logging asdm
informational
mtu outside 1500
mtu inside 1500
mtu management
1500
no asdm history enable
arp timeout 14400
global (outside) 1 interface 一定要打表示 PAT端口扩展：“1”为其
href="tag.php?name=NAT">NAT ID
nat (inside) 1 10.1.0.0 255.255.0.0  转换所有10.1.0.0 的内部地址
route outside 0.0.0.0 0.0.0.0 192.168.3.254 1
内部所有地址访问外部地址出口为 电信－网通 提供的网关地址
timeout xlate 3:00:00
timeout conn 1:00:00
half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323
0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00
sip_media 0:02:00
timeout uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 management
no snmp-server
location
no snmp-server contact
snmp-server enable traps snmp
authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout
5
console timeout 0
dhcpd address 10.1.1.30-10.1.1.200 inside class=t_tag onclick=tagshow(event) href="tag.php?name=DHCP">DHCP 自动提供分配范围
为10.1.1.30－200
dhcpd address 192.168.1.2-192.168.1.254 management 无效
dhcpd dns 192.168.0.1 DNS 添加：可以是电信网通提供 直接添加，或者自己的DNS
onclick=tagshow(event)
href="tag.php?name=������">服务器地址。
dhcpd lease 3600
dhcpd ping_timeout 50
dhcpd domain suzhou.jy 域名
dhcpd enable inside 打开内部网段自动分配
dhcpd enable management
无效
Cryptochecksum:6148633dac00f8f7a3418833f98d5ad4
access-group icmp_in in
interface outside 这两句表示，
access-list icmp_in extended permit icmp any any
润许PING包发送或接收
: end