每天一个linux命令(网络):【转载】ping命令
Linux系统的ping命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”、不能打开网页时会说“你先ping网关地址192.168.1.1试试”。它通过发送ICMP ECHO_REQUEST数据包到网络主机(send ICMP ECHO_REQUEST to network hosts),并显示响应情况,这样我们就可以根据它输出的信息来确定目标主机是否可访问(但这不是绝对的)。有些服务器为了防止通过ping探测到,通过防火墙设置了禁止ping或者在内核参数中禁止ping,这样就不能通过ping确定该主机是否还处于开启状态。
linux下的ping和windows下的ping稍有区别,linux下ping不会自动终止,需要按ctrl+c终止或者用参数-c指定要求完成的回应次数。
1.命令格式:
ping [参数] [主机名或IP地址]
2.命令功能:
ping命令用于:确定网络和各外部主机的状态;跟踪和隔离硬件和软件问题;测试、评估和管理网络。如果主机正在运行并连在网上,它就对回送信号进行响应。每个回送信号请求包含一个网际协议(IP)和 ICMP 头,后面紧跟一个 tim 结构,以及来填写这个信息包的足够的字节。缺省情况是连续发送回送信号请求直到接收到中断信号(Ctrl-C)。
ping 命令每秒发送一个数据报并且为每个接收到的响应打印一行输出。ping 命令计算信号往返时间和(信息)包丢失情况的统计信息,并且在完成之后显示一个简要总结。ping 命令在程序超时或当接收到 SIGINT 信号时结束。Host 参数或者是一个有效的主机名或者是因特网地址。
3.命令参数:
-d 使用Socket的SO_DEBUG功能。
-f 极限检测。大量且快速地送网络封包给一台机器,看它的回应。
-n 只输出数值。
-q 不显示任何传送封包的信息,只显示最后的结果。
-r 忽略普通的Routing Table,直接将数据包送到远端主机上。通常是查看本机的网络接口是否有问题。
-R 记录路由过程。
-v 详细显示指令的执行过程。
<p>-c 数目:在发送指定数目的包后停止。
-i 秒数:设定间隔几秒送一个网络封包给一台机器,预设值是一秒送一次。
-I 网络界面:使用指定的网络界面送出数据包。
-l 前置载入:设置在送出要求信息之前,先行发出的数据包。
-p 范本样式:设置填满数据包的范本样式。
-s 字节数:指定发送的数据字节数,预设值是56,加上8字节的ICMP头,一共是64ICMP数据字节。
-t 存活数值:设置存活数值TTL的大小。
4.使用实例:
实例1:ping的通的情况
命令:
ping 192.168.120.205
输出:
[root@localhost ~]# ping 192.168.120.205
PING 192.168.120.205 (192.168.120.205) () bytes of data.
bytes from 192.168.120.205: icmp_seq= ttl= time=0.720 ms
bytes from 192.168.120.205: icmp_seq= ttl= time=0.181 ms
bytes from 192.168.120.205: icmp_seq= ttl= time=0.191 ms
bytes from 192.168.120.205: icmp_seq= ttl= time=0.188 ms
bytes from 192.168.120.205: icmp_seq= ttl= time=0.189 ms --- 192.168.120.205 ping statistics ---
packets transmitted, received, % packet loss, time 4000ms
rtt min/avg/max/mdev = 0.181/0.293/0.720/0.214 ms
[root@localhost ~]#
实例2:ping不通的情况
命令:
ping 192.168.120.202
输出:
[root@localhost ~]# ping 192.168.120.202
PING 192.168.120.202 (192.168.120.202) () bytes of data.
From 192.168.120.204 icmp_seq= Destination Host Unreachable
From 192.168.120.204 icmp_seq= Destination Host Unreachable
From 192.168.120.204 icmp_seq= Destination Host Unreachable
From 192.168.120.204 icmp_seq= Destination Host Unreachable
From 192.168.120.204 icmp_seq= Destination Host Unreachable
From 192.168.120.204 icmp_seq= Destination Host Unreachable --- 192.168.120.202 ping statistics ---
packets transmitted, received, + errors, % packet loss, time 7005ms
, pipe
[root@localhost ~]#
实例3:ping网关
命令:
ping -b 192.168.120.1
输出:
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG eth0
default 192.168.120.240 0.0.0.0 UG eth0
[root@localhost ~]# ping -b 192.168.120.1
PING 192.168.120.1 (192.168.120.1) () bytes of data.
bytes from 192.168.120.1: icmp_seq= ttl= time=2.02 ms
bytes from 192.168.120.1: icmp_seq= ttl= time=1.83 ms
bytes from 192.168.120.1: icmp_seq= ttl= time=1.68 ms
bytes from 192.168.120.1: icmp_seq= ttl= time=1.98 ms
bytes from 192.168.120.1: icmp_seq= ttl= time=1.88 ms --- 192.168.120.1 ping statistics ---
packets transmitted, received, % packet loss, time 4000ms
rtt min/avg/max/mdev = 1.682/1.880/2.020/0.129 ms
实例4:ping指定次数
命令:
ping -c 10 192.168.120.206
输出:
[root@localhost ~]# ping -c 192.168.120.206
PING 192.168.120.206 (192.168.120.206) () bytes of data.
bytes from 192.168.120.206: icmp_seq= ttl= time=1.25 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.260 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.242 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.271 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.274 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.295 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.269 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.270 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.253 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.289 ms --- 192.168.120.206 ping statistics ---
packets transmitted, received, % packet loss, time 9000ms
rtt min/avg/max/mdev = 0.242/0.367/1.251/0.295 ms
[root@localhost ~]#
实例5:时间间隔和次数限制的ping
命令:
ping -c 10 -i 0.5 192.168.120.206
输出:
[root@localhost ~]# ping -c -i 0.5 192.168.120.206
PING 192.168.120.206 (192.168.120.206) () bytes of data.
bytes from 192.168.120.206: icmp_seq= ttl= time=1.24 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.235 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.244 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.300 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.255 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.264 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.263 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.331 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.247 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.244 ms --- 192.168.120.206 ping statistics ---
packets transmitted, received, % packet loss, time 4499ms
rtt min/avg/max/mdev = 0.235/0.362/1.241/0.294 ms
[root@localhost ~]# ping -c -i 0.01 192.168.120.206
PING 192.168.120.206 (192.168.120.206) () bytes of data.
bytes from 192.168.120.206: icmp_seq= ttl= time=0.244 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.195 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.219 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.204 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=3.56 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=1.93 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.193 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.193 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.202 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.211 ms --- 192.168.120.206 ping statistics ---
packets transmitted, received, % packet loss, time 90ms
rtt min/avg/max/mdev = 0.193/0.716/3.564/1.080 ms
[root@localhost ~]#
实例6:通过域名ping公网上的站点
命令:
ping -c 5 www.58.com
输出:
peida-VirtualBox ~ # ping -c www..com
PING www..com (211.151.111.30) () bytes of data.
bytes from 211.151.111.30: icmp_req= ttl= time=14.7 ms
bytes from 211.151.111.30: icmp_req= ttl= time=16.4 ms
bytes from 211.151.111.30: icmp_req= ttl= time=15.2 ms
bytes from 211.151.111.30: icmp_req= ttl= time=14.6 ms
bytes from 211.151.111.30: icmp_req= ttl= time=19.9 ms --- www..com ping statistics ---
packets transmitted, received, % packet loss, time 20101ms
rtt min/avg/max/mdev = 14.618/16.192/19.917/1.965 ms
peida-VirtualBox ~ #
实例7:多参数使用
命令:
ping -i 3 -s 1024 -t 255 192.168.120.206
输出:
[root@localhost ~]# ping -i -s -t 192.168.120.206
PING 192.168.120.206 (192.168.120.206) () bytes of data.
bytes from 192.168.120.206: icmp_seq= ttl= time=1.99 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.694 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.300 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.481 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.415 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.600 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.411 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.281 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.318 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.362 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.408 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.445 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.397 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.406 ms
bytes from 192.168.120.206: icmp_seq= ttl= time=0.458 ms --- 192.168.120.206 ping statistics ---
packets transmitted, received, % packet loss, time 41999ms
rtt min/avg/max/mdev = 0.281/0.531/1.993/0.404 ms
[root@localhost ~]#
说明:
-i 3 发送周期为 3秒 -s 设置发送包的大小为1024 -t 设置TTL值为 255
每天一个linux命令(网络):【转载】ping命令的更多相关文章
- linux查看网络链接状况命令netstat
linux查看网络链接状况命令 netstat 参数如下: -a 显示所有socket,包括正在监听的. -c 每隔1秒就重新显示一遍,直到用户中断它. -i 显示所有网络接口的信息,格式同“ifco ...
- Linux和Windows下ping命令详解(转:http://linux.chinaitlab.com/command/829332.html)
一.Linux下的ping参数 用途 发送一个回送信号请求给网络主机. 语法 ping [ -d] [ -D ] [ -n ] [ -q ] [ -r] [ -v] [ \ -R ] [ -a add ...
- Linux和Windows下ping命令详解
转:http://linux.chinaitlab.com/command/829332.html 一.Linux下的ping参数 用途 发送一个回送信号请求给网络主机. 语法 ping [ -d] ...
- Linux服务架设篇--ping命令
工作原理: 向远程机发送包含一定字节数的ICMP数据包,如果能收到对方的回复的数据包,就表明网络是相通的,而且根据两个数据包的时间差,还可以知道相互之间网络链接的速度. 注意: 有些远程主机由于某种原 ...
- Linux系统下如何禁止ping命令或允许ping命令的方法
1.禁止pingecho 1 >/proc/sys/net/ipv4/icmp_echo_ignore_all 2.允许ping echo 0 >/proc/sys/net/ipv4/ic ...
- Linux系统关闭对ping命令做响应。
1.测试 ping 192.168.10.5 可以正常ping通, 2,修改 /proc/sys/net/ipv4/icmp_echo_ignore_all 文件的值=1 3.在测试 已经ping不 ...
- 每天一个linux命令(54):ping命令
Linux系统的ping命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”.不能打开网页时会说“你先ping网关地址192.168.1.1试试”. ...
- 每天一个linux命令(46):ping命令
Linux系统的ping 命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”.不能打开网页时会说“你先ping网关地 址192.168.1.1试试 ...
- LINUX网络之ifconfig命令与ping
ifconfig命令 网络配置 ifconfig命令被用于配置和显示Linux内核中网络接口的网络参数.用ifconfig命令配置的网卡信息,在网卡重启后机器重启后,配置就不存在.要想将上述的配置信息 ...
- 【转】每天一个linux命令(54):ping命令
原文网址:http://www.cnblogs.com/peida/archive/2013/03/06/2945407.html Linux系统的ping命令是常用的网络命令,它通常用来测试与目标主 ...
随机推荐
- python openpyxl 封装Execl常用操作的方法
封装Excel操作方法:先装openpyxl:pip install openpyxl==2.4.5(可以指定版本) 封装脚本:#encoding=utf-8 from openpyxl import ...
- Dom 重绘重排
https://juejin.im/entry/590801780ce46300617c89b8 DOM 重绘重排
- WebCollector2.7爬虫框架——在Eclipse项目中配置
WebCollector2.7爬虫框架——在Eclipse项目中配置 在Eclipse项目中使用WebCollector爬虫非常简单,不需要任何其他的配置,只需要导入相关的jar包即可. Netbea ...
- MSF基础攻击实践报告
MSF基础攻击实践 MSF的六个模块:exploit,encoder,payload,aux,post,nops exploit——渗透攻击模块 测试者利用它来攻击一个系统,程序,或服务,以获得开发者 ...
- fiddler几种功能强大的用法(二)
参考网址:http://blog.rekfan.com/articles/228.html http://www.cnblogs.com/tugenhua0707/p/4637771.html htt ...
- UVa 11582 巨大的斐波那契数!(幂取模)
https://vjudge.net/problem/UVA-11582 题意: 输入两个非负整数a.b和正整数n,你的任务是计算f(a^b)除以n的余数.f[0]=0,f[1]=1,f[i+2]=f ...
- hdu 2444 The Accomodation of Students 判断二分图+二分匹配
The Accomodation of Students Time Limit: 5000/1000 MS (Java/Others) Memory Limit: 32768/32768 K ( ...
- python 获取列表大于指定长度的元素
def long_words(n, str): word_len = [] txt = str.split(" ") for x in txt: if len(x) > n: ...
- python 字符串压缩
import zlib s = b'witch which has which witches wrist watch' print(len(s)) t = zlib.compress(s) prin ...
- 构建工具 Ant、Maven和Gradle
构建工具的作用 依赖管理 测试,打包,发布 主流的构建工具 Ant:提供编译,测试,打包 Maven:在Ant的基础上提供了依赖管理和发布的功能 Gradle:在Maven的基础上使用Groovy管理 ...