IEEE 754标准
IEEE 754-1985 was an industry standard for representing floating-point numbers in computers, officially adopted in 1985 and superseded in 2008 by IEEE 754-2008. During its 23 years, it was the most widely used format for floating-point computation. It was implemented in software, in the form of floating-point libraries, and in hardware, in the instructions of many CPUs and FPUs. The first integrated circuit to implement the draft of what was to become IEEE 754-1985 was the Intel 8087.
IEEE 754-1985 represents numbers in binary, providing definitions for four levels of precision, of which the two most commonly used are:
level | width | range | precision* |
---|---|---|---|
single precision | 32 bits | ±1.18×10−38 to ±3.4×1038 | approx. 7 decimal digits |
double precision | 64 bits | ±2.23×10−308 to ±1.80×10308 | approx. 15 decimal digits |
- Precision: The number of decimal digits precision is calculated via number_of_mantissa_bits * Log10(2). Thus ~7.2 and ~15.9 for single and double precision respectively.
The standard also defines representations for positive and negative infinity, a "negative zero", five exceptions to handle invalid results like division by zero, special values called NaNs for representing those exceptions,denormal numbers to represent numbers smaller than shown above, and four rounding modes.
Contents[hide] |
[edit] Representation of numbers
Floating-point numbers in IEEE 754 format consist of three fields: a sign bit, a biased exponent, and a fraction. The following example illustrates the meaning of each.
The decimal number 0.1562510 represented in binary is 0.001012 (that is, 1/8 + 1/32). (Subscripts indicate the number base.) Analogous to scientific notation, where numbers are written to have a single non-zero digit to the left of the decimal point, we rewrite this number so it has a single 1 bit to the left of the "binary point". We simply multiply by the appropriate power of 2 to compensate for shifting the bits left by three positions:
Now we can read off the fraction and the exponent: the fraction is .012 and the exponent is −3.
As illustrated in the pictures, the three fields in the IEEE 754 representation of this number are:
- sign = 0, because the number is positive. (1 indicates negative.)
- biased exponent = −3 + the "bias". In single precision, the bias is 127, so in this example the biased exponent is 124; in double precision, the bias is 1023, so the biased exponent in this example is 1020.
- fraction = .01000…2.
IEEE 754 adds a bias to the exponent so that numbers can in many cases be compared conveniently by the same hardware that compares signed 2's-complement integers. Using a biased exponent, the lesser of two positive floating-point numbers will come out "less than" the greater following the same ordering as for sign and magnitude integers. If two floating-point numbers have different signs, the sign-and-magnitude comparison also works with biased exponents. However, if both biased-exponent floating-point numbers are negative, then the ordering must be reversed. If the exponent were represented as, say, a 2's-complement number, comparison to see which of two numbers is greater would not be as convenient.
The leading 1 bit is omitted since all numbers except zero start with a leading 1; the leading 1 is implicit and doesn't actually need to be stored which gives an extra bit of precision for "free."
[edit] Zero
The number zero is represented specially:
- sign = 0 for positive zero, 1 for negative zero.
- biased exponent = 0.
- fraction = 0.
[edit] Denormalized numbers
The number representations described above are called normalized, meaning that the implicit leading binary digit is a 1. To reduce the loss of precision when an underflow occurs, IEEE 754 includes the ability to represent fractions smaller than are possible in the normalized representation, by making the implicit leading digit a 0. Such numbers are called denormal. They don't include as many significant digits as a normalized number, but they enable a gradual loss of precision when the result of an arithmetic operation is not exactly zero but is too close to zero to be represented by a normalized number.
A denormal number is represented with a biased exponent of all 0 bits, which represents an exponent of −126 in single precision (not −127), or −1022 in double precision (not −1023).[1] In contrast, the smallest biased exponent representing a normal number is 1 (see examples below).
[edit] Representation of non-numbers
The biased-exponent field is filled with all 1 bits to indicate either infinity or an invalid result of a computation.
[edit] Positive and negative infinity
Positive and negative infinity are represented thus:
- sign = 0 for positive infinity, 1 for negative infinity.
- biased exponent = all 1 bits.
- fraction = all 0 bits.
[edit] NaN
Some operations of floating-point arithmetic are invalid, such as dividing by zero or taking the square root of a negative number. The act of reaching an invalid result is called a floating-point exception. An exceptional result is represented by a special code called a NaN, for "Not a Number". All NaNs in IEEE 754-1985 have this format:
- sign = either 0 or 1.
- biased exponent = all 1 bits.
- fraction = anything except all 0 bits (since all 0 bits represents infinity).
[edit] Range and precision
Precision is defined as the minimum difference between two successive mantissa representations; thus it is a function only in the mantissa; while the gap is defined as the difference between two successive numbers.[2]
[edit] Single precision
Single-precision numbers occupy 32 bits. In single precision:
- The positive and negative numbers closest to zero (represented by the denormalized value with all 0s in the exponent field and the binary value 1 in the fraction field) are
- ±2−149 ≈ ±1.4012985×10−45
- The positive and negative normalized numbers closest to zero (represented with the binary value 1 in the exponent field and 0 in the fraction field) are
- ±2−126 ≈ ±1.175494351×10−38
- The finite positive and finite negative numbers furthest from zero (represented by the value with 254 in the exponent field and all 1s in the fraction field) are
- ±(1−2−24)×2128[3] ≈ ±3.4028235×1038
Some example range and gap values for given exponents in single precision:
Actual Exponent (unbiased) | Exp (biased) | Minimum | Maximum | Gap |
---|---|---|---|---|
0 | 127 | 1 | 1.999999880791 | 1.19209289551e−7 |
1 | 128 | 2 | 3.99999976158 | 2.38418579102e−7 |
2 | 129 | 4 | 7.99999952316 | 4.76837158203e−7 |
10 | 137 | 1024 | 2047.99987793 | 1.220703125e−4 |
11 | 138 | 2048 | 4095.99975586 | 2.44140625e−4 |
23 | 150 | 8388608 | 16777215 | 1 |
24 | 151 | 16777216 | 33554430 | 2 |
127 | 254 | 1.7014e38 | 3.4028e38 | 2.02824096037e31 |
As an example, 16,777,217 can not be encoded as a 32-bit float as it will be rounded to 16,777,216. This shows why floating point arithmetic is unsuitable for accounting software. However, all integers within the representable range that are a power of 2 can be stored in a 32-bit float without rounding.
[edit] Double precision
Double-precision numbers occupy 64 bits. In double precision:
- The positive and negative numbers closest to zero (represented by the denormalized value with all 0s in the Exp field and the binary value 1 in the Fraction field) are
- ±2−1074 ≈ ±5×10−324
- The positive and negative normalized numbers closest to zero (represented with the binary value 1 in the Exp field and 0 in the fraction field) are
- ±2−1022 ≈ ±2.2250738585072020×10−308
- The finite positive and finite negative numbers furthest from zero (represented by the value with 2046 in the Exp field and all 1s in the fraction field) are
- ±((1−(1/2)53)21024)[3] ≈ ±1.7976931348623157×10308
Some example range and gap values for given exponents in double precision:
Actual Exponent (unbiased) | Exp (biased) | Minimum | Maximum | Gap |
---|---|---|---|---|
0 | 1023 | 1 | 1.9999999999999997 | 2.2204460492503130808472633e−16 |
1 | 1024 | 2 | 3.9999999999999995 | 8.8817841970012523233890533447266e−16 |
2 | 1025 | 4 | 7.9999999999999990 | 3.5527136788005009293556213378906e−15 |
10 | 1033 | 1024 | 2047.9999999999997 | 2.27373675443232059478759765625e−13 |
11 | 1034 | 2048 | 4095.9999999999995 | 4.5474735088646411895751953125e−13 |
52 | 1075 | 4503599627370496 | 9007199254740991 | 1 |
53 | 1076 | 9007199254740992 | 18014398509481982 | 2 |
1023 | 2046 | 8.9884656743115800e307 | 1.7976931348623157e308 | 1.9958403095347198116563727130368e292 |
[edit] Extended formats
The standard also recommends extended format(s) to be used to perform internal computations at a higher precision than that required for the final result, to minimise round-off errors: the standard only specifies minimum precision and exponent requirements for such formats. The x87 80-bit extended format is the most commonly implemented extended format that meets these requirements.
[edit] Examples
Here are some examples of single-precision IEEE 754 representations:
Type | Sign | Actual Exponent | Exp (biased) | Exponent field | Significand (fraction field) | Value |
---|---|---|---|---|---|---|
Zero | 0 | −127 | 0 | 0000 0000 | 000 0000 0000 0000 0000 0000 | 0.0 |
Negative zero | 1 | −127 | 0 | 0000 0000 | 000 0000 0000 0000 0000 0000 | −0.0 |
One | 0 | 0 | 127 | 0111 1111 | 000 0000 0000 0000 0000 0000 | 1.0 |
Minus One | 1 | 0 | 127 | 0111 1111 | 000 0000 0000 0000 0000 0000 | −1.0 |
Smallestdenormalized number | * | −127 | 0 | 0000 0000 | 000 0000 0000 0000 0000 0001 | ±2−23 × 2−126 = ±2−149 ≈ ±1.4×10−45 |
"Middle" denormalized number | * | −127 | 0 | 0000 0000 | 100 0000 0000 0000 0000 0000 | ±2−1 × 2−126 = ±2−127 ≈ ±5.88×10−39 |
Largest denormalized number | * | −127 | 0 | 0000 0000 | 111 1111 1111 1111 1111 1111 | ±(1−2−23) × 2−126 ≈ ±1.18×10−38 |
Smallest normalized number | * | −126 | 1 | 0000 0001 | 000 0000 0000 0000 0000 0000 | ±2−126 ≈ ±1.18×10−38 |
Largest normalized number | * | 127 | 254 | 1111 1110 | 111 1111 1111 1111 1111 1111 | ±(2−2−23) × 2127 ≈ ±3.4×1038 |
Positive infinity | 0 | 128 | 255 | 1111 1111 | 000 0000 0000 0000 0000 0000 | +∞ |
Negative infinity | 1 | 128 | 255 | 1111 1111 | 000 0000 0000 0000 0000 0000 | −∞ |
Not a number | * | 128 | 255 | 1111 1111 | non zero | NaN |
* Sign bit can be either 0 or 1 . |
[edit] Comparing floating-point numbers
Every possible bit combination is either a NaN or a number with a unique value in the affinely extended real number system with its associated order, except for the two bit combinations negative zero and positive zero, which sometimes require special attention (see below). The binary representation has the special property that, excluding NaNs, any two numbers can be compared like sign and magnitude integers (although with modern computer processors this is no longer directly applicable): if the sign bit is different, the negative number precedes the positive number (except that negative zero and positive zero should be considered equal), otherwise, relative order is the same as lexicographical order but inverted for two negative numbers;endianness issues apply.
Floating-point arithmetic is subject to rounding that may affect the outcome of comparisons on the results of the computations.
Although negative zero and positive zero are generally considered equal for comparison purposes, someprogramming language relational operators and similar constructs might or do treat them as distinct. According to the Java Language Specification,[4] comparison and equality operators treat them as equal, but Math.min() and Math.max() distinguish them (officially starting with Java version 1.1 but actually with 1.1.1), as do the comparison methods equals(), compareTo() and even compare() of classes Float and Double.
[edit] Rounding floating-point numbers
The IEEE standard has four different rounding modes; the first is the default; the others are called directed roundings.
- Round to Nearest – rounds to the nearest value; if the number falls midway it is rounded to the nearest value with an even (zero) least significant bit, which occurs 50% of the time (in IEEE 754-2008 this mode is called roundTiesToEven to distinguish it from another round-to-nearest mode)
- Round toward 0 – directed rounding towards zero
- Round toward +∞ – directed rounding towards positive infinity
- Round toward −∞ – directed rounding towards negative infinity.
[edit] Extending the real numbers
The IEEE standard employs (and extends) the affinely extended real number system, with separate positive and negative infinities. During drafting, there was a proposal for the standard to incorporate the projectively extended real number system, with a single unsigned infinity, by providing programmers with a mode selection option. In the interest of reducing the complexity of the final standard, the projective mode was dropped, however. The Intel 8087 and Intel 80287 floating point co-processors both support this projective mode.[5][6][7]
[edit] Functions and predicates
[edit] Standard operations
The following functions must be provided:
- Add, subtract, multiply, divide
- Square root
- Floating point remainder. This is not like a normal modulo operation, it can be negative for two positive numbers. It returns the exact value of x–(round(x/y)·y).
- Round to nearest integer. For undirected rounding when halfway between two integers the even integer is chosen.
- Comparison operations. Besides the more obvious results, IEEE 754 defines that −∞ = −∞, +∞ = +∞ andx ≠
NaN
for any x (includingNaN
).
[edit] Recommended functions and predicates
- Under some C compilers,
copysign(x,y)
returns x with the sign of y, soabs(x)
equalscopysign(x,1.0)
. This is one of the few operations which operates on a NaN in a way resembling arithmetic. The functioncopysign
is new in the C99 standard. - −x returns x with the sign reversed. This is different from 0−x in some cases, notably when x is 0. So −(0) is −0, but the sign of 0−0 depends on the rounding mode.
scalb(y, N)
logb(x)
finite(x)
a predicate for "x is a finite value", equivalent to −Inf < x < Infisnan(x)
a predicate for "x is a NaN", equivalent to "x ≠ x"x <> y
which turns out to have different exception behavior than NOT(x = y).unordered(x, y)
is true when "x is unordered with y", i.e., either x or y is a NaN.class(x)
nextafter(x,y)
returns the next representable value from x in the direction towards y
[edit] History
In 1976 Intel began planning to produce a floating point coprocessor. Dr John Palmer, the manager of the effort, persuaded them that they should try to develop a standard for all their floating point operations. William Kahanwas hired as a consultant; he had helped improve the accuracy of Hewlett Packard's calculators. Kahan initially recommended that the floating point base be decimal[8] but the hardware design of the coprocessor was too far advanced to make that change.
The work within Intel worried other vendors, who set up a standardization effort to ensure a 'level playing field'. Kahan attended the second IEEE 754 standards working group meeting, held in November 1977. Here, he received permission from Intel to put forward a draft proposal based on the standard arithmetic part of their design for a coprocessor. The arguments over gradual underflow lasted until 1981 when an expert commissioned by DEC to assess it sided against the dissenters.
Even before it was approved, the draft standard had been implemented by a number of manufacturers.[9][10]The Intel 8087, which was announced in 1980, was the first chip to implement the draft standard.
[edit] See also
- IEEE 754-2008
- −0 (negative zero)
- Intel 8087
- minifloat for simple examples of properties of IEEE 754 floating point numbers
- Fixed-point arithmetic
[edit] References
- ^ Hennessy. Computer Organization and Design. Morgan Kaufmann. p. 270.
- ^ Computer Arithmetic; Hossam A. H. Fahmy, Shlomo Waser, and Michael J. Flynn;http://arith.stanford.edu/~hfahmy/webpages/arith_class/arith.pdf
- ^ a b Prof. W. Kahan (PDF). Lecture Notes on the Status of IEEE 754. October 1, 1997 3:36 am. Elect. Eng. & Computer Science University of California.http://www.cs.berkeley.edu/~wkahan/ieee754status/IEEE754.PDF. Retrieved 2007-04-12.
- ^ The Java Language Specification
- ^ John R. Hauser (March 1996). "Handling Floating-Point Exceptions in Numeric Programs" (PDF). ACM Transactions on Programming Languages and Systems 18 (2).http://www.jhauser.us/publications/1996_Hauser_FloatingPointExceptions.html.
- ^ David Stevenson (March 1981). "IEEE Task P754: A proposed standard for binary floating-point arithmetic". IEEE Computer 14 (3): 51–62.
- ^ William Kahan and John Palmer (1979). "On a proposed floating-point standard". SIGNUM Newsletter14 (Special): 13–21. doi:10.1145/1057520.1057522.
- ^ W. Kahan 2003, pers. comm. to Mike Cowlishaw and others after an IEEE 754 meeting
- ^ Charles Severance (20 February 1998). "An Interview with the Old Man of Floating-Point".http://www.eecs.berkeley.edu/~wkahan/ieee754status/754story.html.
- ^ Charles Severance. "History of IEEE Floating-Point Format". Connexions.http://cnx.org/content/m32770/latest/.
[edit] Further reading
- Charles Severance (March 1998). "IEEE 754: An Interview with William Kahan" (PDF). IEEE Computer 31(3): 114–115. doi:10.1109/MC.1998.660194. http://www.freecollab.com/dr-chuck/papers/columns/r3114.pdf. Retrieved 2008-04-28.
- David Goldberg (March 1991). "What Every Computer Scientist Should Know About Floating-Point Arithmetic" (PDF). ACM Computing Surveys 23 (1): 5–48. doi:10.1145/103162.103163.http://www.validlab.com/goldberg/paper.pdf. Retrieved 2008-04-28.
- Chris Hecker (February 1996). "Let's Get To The (Floating) Point" (PDF). Game Developer Magazine: 19–24. ISSN 1073-922X. http://www.d6.com/users/checker/pdfs/gdmfp.pdf.
- David Monniaux (May 2008). "The pitfalls of verifying floating-point computations". ACM Transactions on Programming Languages and Systems 30 (3): article #12. doi:10.1145/1353445.1353446. ISSN 0164-0925. http://hal.archives-ouvertes.fr/hal-00128124/en/.: A compendium of non-intuitive behaviours of floating-point on popular architectures, with implications for program verification and testing.
IEEE 754标准的更多相关文章
- 【算法】解析IEEE 754 标准
目录结构: contents structure [-] 浮点数的存储过程 次正规数(Denormalized Number) 零(zero) 非数值(NaN) 无穷大(infinity) 除数为0. ...
- python 警惕 IEEE 754标准
双精度浮点数格式,即IEEE 754标准 >>> 0.1+0.2 0.30000000000000004 >>> (0.1+0.2)==0.3 False > ...
- 打印一个浮点数组,会输出字符串"Hello, world“ & 浮点数的二进制表示(IEEE 754标准)
#include <stdio.h> #include<stdlib.h> int main() { float a[3] = { 1143139122437582505939 ...
- IEEE 754标准--维基百科
IEEE二进制浮点数算术标准(IEEE 754) 是20世纪80年代以来最广泛使用的浮点数运算标准,为许多CPU与浮点运算器所采用.这个标准定义了表示浮点数的格式(包括负零-0)与反常值(denorm ...
- 基于 IEEE 754 标准的 单精度浮点数计算方式 (未完成)
def dec2bin(dec): if dec < 0: s = ' dec = dec * (-1) else: s = ' e = 127 dec = float(dec) r = int ...
- IEEE二进制浮点数算术标准(IEEE 754)
整理自IEEE 754 IEEE二进制浮点数算术标准(IEEE 754)是20世纪80年代以来最广泛使用的浮点数运算标准,为许多CPU与浮点运算器所采用.这个标准定义了表示浮点数的格式(包括负零-0) ...
- IEEE 754二进制浮点数算术标准
可能很多人都遇到过浮点数精度丢失的问题,下面以JavaScript为例. 1 - 0.9 = 0.09999999999999998 纳尼,不应该是0.1么,怎么变成0.099999999999999 ...
- IEEE 754浮点数表示标准
二进制数的科学计数法 C++中使用的浮点数包括采用的是IEEE标准下的浮点数表示方法.我们知道在数学中可以将任何十进制的数写成以10为底的科学计数法的形式,如下 其中显而易见,因为如果a比10大或者比 ...
- IEEE 754舍入的问题
写在前面 本文的舍入方法只适用于保留0位或1位小数,个人水平所限,暂时没有发现保留更多小数位的舍入的规律- IEEE 754的舍入模式 IEEE 754标准提供了2类,5种舍入模式,在默认情况下一般是 ...
随机推荐
- 汇编写hello world
.global main main: mov ip, sp stmfd sp!, {fp, ip, lr} sub fp, ip, # ldr r0, =he mov lr, pc b printf ...
- 退货行RMA编号改为必输选项
应用 Oracle Inventory 层 Level Function 函数名 Funcgtion Name RCV_RCVTXERE 表单名 Form Name RCVTXERE 说明 Descr ...
- [Leetcode][Python]29: Divide Two Integers
# -*- coding: utf8 -*-'''__author__ = 'dabay.wang@gmail.com' 29: Divide Two Integershttps://oj.leetc ...
- poj2027简单题
#include <stdio.h> #include <stdlib.h> int main() { int n,x,y; scanf("%d",& ...
- [Leetcode][Python]20: Valid Parentheses
# -*- coding: utf8 -*-'''__author__ = 'dabay.wang@gmail.com' 20: Valid Parentheseshttps://oj.leetcod ...
- javascript数组去重算法-----5
<!DOCTYPE html> <html lang="en"> <head> <meta charset="UTF-8&quo ...
- css新属性box-sizing应用
<!doctype html> <html lang="en"> <head> <meta charset="UTF-8&quo ...
- javascript编辑器预览模式解密
<!DOCTYPE html> <html lang="en"> <head> <meta charset="UTF-8&quo ...
- python-聊聊反射
反射 对于初学python可能较难理解,但反射是非常有用. 试想一下,当别的程序传入给你写的这段代码一个变量(var=“math”),这个变量是一个字符串,这个字符串是一个模块或者一个模块下的某个方法 ...
- android 屏幕适配问题【转】
如何将一个应用程序适配在不同的手机上,虽然这不算是一个技术问题,但是对于刚刚做屏幕的开发人员来说,还真不是一件多么简单的事情. 首先:你需要在AndroidManifest.xml文件的<m ...