centos配置vsftpd服务2
ftp搭建
一、搭建前提
a、ssh服务已经开启,b、防火墙关闭,c、连网
1、查看ssh和防火墙的状态
service sshd status
service iptables status
2、开启ssh
service sshd start
3、关闭防火墙
chkconfig iptables off
4、测试是否连网
二、安装并开启tftp和vsftpd
#yum install tftp
#yum install vsftpd
#chkconfig vsftpd on
#chkconfig tftp on
启动vsftpd服务
service vsftpd start
查看vsftpd的启动状态
service vsftpd status
三、打开21和20端口
# /sbin/iptables -I INPUT -p tcp --dport 21 -j ACCEPT
# /sbin/iptables -I INPUT -p tcp --dport 20 -j ACCEPT
# /etc/rc.d/init.d/iptables save
四、添加ftp用户
*进入etc下的vsftpd下再添加
#cd /etc/vsftpd/
#useradd ftpuser
#passwd ftpuser
五、修改vsftpd.conf配置文件
#vi /etc/vsftpd/vsftpd.conf
1、把第一行的 anonymous_enable=YES ,改为NO
**ftpusers:位于/etc/vsftpd/目录下。它指定了哪些用户账户不能访问FTP服务器, 例如root等。
**user_list:位于/etc/vsftpd目录下。该文件里的用户账户在默认情况下也不能访问FTP服务器,仅当vsftpd .conf配置文件里启用userlist_enable=NO选项时才允许访问。
六、重启服务
service vsftpd restart
七、开启SELinux
1、getsebool -a | grep ftp :查看SELinux下是否开启ftp的支持
把allow_ftpd_full_access --> off,
ftp_home_dir --> off 都改为on。
#setsebool ftp_home_dir 1
#setsebool allow_ftpd_full_access 1
(*如果出现getsebool: SELinux is disabled的错误,需重新开启selinux
#vi etc/selinux/config
*SELinux=enable
*重启linux,开启selinux)
ftp登录
1、ftp +ip地址
2、name:
3、password:
4、返回Login successful登录成功
ftp目录操作
1、ls :列出当前文件夹下所有文件
2、cd :和linux操作一样切换位置
ftp文件下载
1、lcd :指定下载到的位置 (eg:lcd c:\test\)
2、getfile :下载文件 (eg:get index.html 然后瞎子啊到指定位置)
mgetfile :下载多个文件 (eg:mget *.xls 下载以xls后缀的所有文件)
ftp文件上传
1、put file :上传文件到指定的ftp上传文件位置
mput file :上传多个文件
ftp关闭
1、bye 2、exit 3、quit
ftp搭建问题
500 OOPS: cannot change directory:/home/***
是路径目录错误,解决方法:
在配置文件中添加或更改默认访问路径文件
在vsftpd.conf最后添加 local_root=/home :登录后就会默认访问这个路径下的文件夹
***ftp权限设置(/etc/vsftpd/vsftpd.conf下)***
1、在配置文件最后添加chroot_local_user=YES
或者把配置中#chroot_local_user=YES的‘#’去掉 把所有的本地用户限制在给定的访问路径下的文件夹里
如果只限制一些用户,则
chroot_local_user=NO
#chroot_list_enable=YES
#(default follows)
#chroot_list_file=/etc/vsftpd/chroot_list
//去掉‘#’,chroot_local_user改为NO
:将要限制的用户添加到此文件里面
具体配置:
根据 /etc/vsftpd/vsftpd.conf默认配置给出设定功能
# Example config file /etc/vsftpd/vsftpd.conf
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=YES
允许匿名用户登录
# Uncomment this to allow local users to log in.
local_enable=YES
允许系统用户名登录
# Uncomment this to enable any form of FTP write command.
write_enable=YES
允许使用任何可以修改文件系统的FTP的指令
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
本地用户新增档案的权限
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
允许匿名用户上传文件
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
允许匿名用户创建新目录
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
允许为目录配置显示信息,显示每个目录下面的message_file文件的内容
# Activate logging of uploads/downloads.
xferlog_enable=YES
开启日记功能
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
使用标准的20端口来连接ftp
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
所有匿名上传的文件的所属用户将会被更改成chown_username
#chown_username=whoever
匿名上传文件所属用户名
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
日志文件位置
# If you want, you can have your log file in standard ftpd xferlog format
xferlog_std_format=YES
使用标准格式
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
空闲连接超时
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
数据传输超时
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
当服务器运行于最底层时使用的用户名
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
允许使用\"async ABOR\"命令,一般不用,容易出问题
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
管控是否可用ASCII 模式上传。默认值为NO
#ascii_download_enable=YES
管控是否可用ASCII 模式下载。默认值为NO
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
login时显示欢迎信息.如果设置了banner_file则此设置无效
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
如果匿名用户需要密码,那么使用banned_email_file里面的电子邮件地址的用户不能登录
# (default follows)
#banned_email_file=/etc/vsftpd/banned_emails
禁止使用匿名用户登陆时作为密码的电子邮件地址
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#chroot_list_enable=YES
如果启动这项功能,则所有列在chroot_list_file中的使用者不能更改根目录
# (default follows)
#chroot_list_file=/etc/vsftpd/chroot_list
定义不能更改用户主目录的文件
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
是否能使用ls -R命令以防止浪费大量的服务器资源
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=YES
绑定到listen_port指定的端口,既然都绑定了也就是每时都开着的,就是那个什么
standalone模式
# This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6
# sockets, you must run two copies of vsftpd whith two configuration files.
# Make sure, that one of the listen options is commented !!
#listen_ipv6=YES
pam_service_name=vsftpd
定义PAM 所使用的名称,预设为vsftpd
userlist_enable=YES
若启用此选项,userlist_deny选项才被启动
tcp_wrappers=YES
开启tcp_wrappers支持
anonymous_enable=YES
local_enable=YES
write_enable=YES
local_umask=022
#anon_upload_enable=YES
#anon_mkdir_write_enable=YES
dirmessage_enable=YES
xferlog_enable=YES
connect_from_port_20=YES
#chown_uploads=YES
#chown_username=whoever
#xferlog_file=/var/log/vsftpd.log
xferlog_std_format=YES
#idle_session_timeout=600
#data_connection_timeout=120
#nopriv_user=ftpsecure
#async_abor_enable=YES
#ascii_upload_enable=YES
#ascii_download_enable=YES
#ftpd_banner=Welcome to blah FTP service.
#deny_email_enable=YES
#banned_email_file=/etc/vsftpd/banned_emails
#chroot_list_enable=YES
#chroot_list_file=/etc/vsftpd/chroot_list
#ls_recurse_enable=YES
listen=YES
#listen_ipv6=YES
pam_service_name=vsftpd
userlist_enable=YES
tcp_wrappers=YES
centos配置vsftpd服务2的更多相关文章
- Linux环境下安装配置vsftpd服务(三种认证模式)
一.FTP简介 文件传输协议(英文:File Transfer Protocol,缩写:FTP)是用于在网络上进行文件传输的一套标准协议.它工作于网络传输协议的应用层,使用客户/服务器模式,主要是用来 ...
- ubuntu 12.04 配置vsftpd 服务,添加虚拟用户,ssl加密
1.对于12.04的vsftpd 有一些bug,推荐安装版本vsftpd_2.3.5-1ubuntu2ppa1_amd64.debapt-get install python-software-pro ...
- Centos配置tomcat服务并且开机自启动
把要配置成服务的tomcat文件夹中的catalina.sh脚本文件拷一份到/etc/init.d目录,并且改文件名称为tomcat6 cp /usr/web/tomcat/tomcat-/bin/c ...
- CentOS配置VSFTP服务
1.安装vsftpd a.查看是否安装vsftp [root@wsyjlly ~]# rpm -q vsftpd package vsftpd is not installed b.如果没有则安装vs ...
- centos配置nfs服务详细步骤(centos开启nfs服务)
一.NFS服务简介 NFS 是Network File System的缩写,即网络文件系统.一种使用于分散式文件系统的协定,由Sun公司开发,于1984年向外公布.功能是通过网络让不同的机器.不同的操 ...
- centos配置ssh服务并简单测试
最近在做计算机集群方面的东西,简单弄了一下ssh服务. 首先把前提情况介绍一下: 1.我是用的虚拟机先模拟的,也不是没有真机,就是跑来跑去麻烦. 2.装了三个相同配置的centos虚拟机,详细参数就不 ...
- Centos配置vsftpd
#安装vsftpdyum install vsftpd #限制用户只能访问配置的目录,不能访问其他路径#修改vi /etc/vsftpd/vsftpd.conf chroot_list_enable= ...
- centos 配置 ssl服务
使用的是appach 2.4.10 版本 各个版本配置不同 1.首先修改httpd.conf 文件 appach 安装目录下的 conf文件夹中找到 #LoadModule socache_shmcb ...
- CentOS配置vsftpd遇到550错误的解决办法
默认情况下用root是无法连接的,你可以创建一个非root帐户登录,但是登录是可以登录,却没有办法创建或是上传文件.有人说,可以把 SELinux关掉,可是这样未免也有点尺度太大了,其实是SELinu ...
随机推荐
- javascript对象属性和数组的访问
javascript对象属性的访问 假如有对象test:var test = { "a":1, "b":2};直接访问对象test的属性a的值,有两种方法: ...
- 查看MySQL 连接信息--连接空闲时间及正在执行的SQL
MySQL 客户端与MySQL server建立连接后,就可以执行SQL语句了. 如何查看一个连接上是否正在执行SQL语句,或者连接是否处于空闲呢? 下面我们做下测试. 1.查看连接的空闲时间 首先看 ...
- 从数组中找出所有组合为s的数
java版本 package numCombine; /** * 从数组中找出所有组合为s的数 * @author root * */ public class NumComberAll { publ ...
- UiUtils
import android.app.Activity; import android.app.Dialog; import android.content.Context; import andro ...
- 小D课堂 - 新版本微服务springcloud+Docker教程_5-07 断路器dashboard监控仪表
笔记 7.断路器Dashboard监控仪表盘实战 简介:讲解断路器Dashboard基础使用和查看 1.加入依赖 <dependency> ...
- File Zilla连接Ubuntu 失败
一.SFTP方式连接失败 站点配置 连接失败 二.FTP连接方式失败 站点配置 连接失败
- mysql安装报vcruntime140.dll缺失
mysql安装报:vcruntime140.dll缺失 安装:Visual C++ Redistributable for Visual Studio 2015 可以解决此问题
- Buffer与Cache的理解
Linux与Windows内存Linux系统的内存机制是优先使用物理内存,当物理内存还有空闲时,Linux系统是不会释放内存的,即使使用过内存的程序已经被关闭,这部分内存就用来做缓存了.换句话说,即使 ...
- 【计算机视觉】OpenCV之GPU与OpenCL的相关内容说明
1 扩展库简介OpenCV(Open Source Computer Vision Library)是一个致力于实时处理计算机视觉问题的开源库.它最初由Intel公司开发,以GPL许可协议发布,后来由 ...
- vue中的样式穿透
参考一下的文章即可: https://www.cnblogs.com/karthuslorin/p/9038854.html http://www.php.cn/js-tutorial-399072. ...