JTAG Simplified So the other day, I explored the JTAG bus interface which is frequently found in CPLDs/FPGAs and is most of the times the sole method of programming and debugging them. It is a powerful interface and very easy to use. I intend to writ…

JTAG Finder Figuring out the JTAG Pinouts on a Device is usually the most time-consuming and frustrating process and Finding the pinouts for these ports allows you to access with correct JTAG Devices likeGPG ORT,  and JTAG Finder helps you to get sta…

SWD and JTAG selection mechanism SWJ-DP enables either an SWD or JTAG protocol to be used on the debug port. To do this, it implements a watcher circuit that detects a specific 16-bit selection sequence on the SWDIOTMS pin: A 16-bit sequence is used…

原文链接:http://www.c-sharpcorner.com/UploadFile/19b1bd/design-patterns-simplified-part3-factory/ Design Patterns Simplified - Part 3 (Simple Factory)[设计模式简述--第三部分(简单工厂)] This article explains why and how to use the Simple Factory Design Pattern in softw…

GPIO_InitTypeDef GPIO_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO, ENABLE);  /********************** 1.执行端口重映射时,复用功能时钟得使能:RCC_APB2Periph_AFIO  2.  &1.GPIO_Remap_SWJ_Disable: !< Full SWJ Disabl…

现象 CPU: STM32107VC 用JLINK 烧写程序时出现NO Cortex-m device found in JTAG chain 如图无法查找到硬件就是CPU 提示1:NO Cortex-M device found inJTAG chain.please check the JTAG cable and the connected devices     提示2:error:flash download failed-target DLL has been cancelled 原…

处女座,为了板子走线美观,拉线方便,在项目量产前,还更改了原来外设的IO口,埋头苦干一天,移植ok,发现PB3一直不听使唤,好,加班检查代码,检查初始化,时钟,IO对应,然后试PCB板,是否短路,断路等等等,试遍了,纹丝不动,拉不高也拉不低...这是为什么呢,百度一下,才发现,PB3是JTAG口之一,需要把IO重映射为普通IO口使用,于是看着大大神们的帖子,回答,代码中,加入了以下两句话: RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);…

原文链接: http://www.c-sharpcorner.com/UploadFile/19b1bd/design-patterns-simplified-part-2-singleton/ Design Patterns Simplified - Part 2 (Singleton)[设计模式简述--第二部分(单例模式)]       I am here to continue the explanation of Design Patterns. Today we will explai…

原文链接:http://www.c-sharpcorner.com/UploadFile/19b1bd/design-patterns-simplified-part1/ Design Patterns Simplified: Part 1[设计模式简述:第一部分] Design patterns are an important consideration when designing or developing any software systems or solutions. There…

同志们,根据ALTERA官方FAE(现场应用工程师)的强烈建议,请注意不要随意带电插拔你的JTAG下载接口,否则会损坏FPGA芯片的JTAG口信号管脚.现象:在排除了下载线的问题后,还是不能访问FPGA的JTAG口,那么很有可能你的FPGA芯片的JTAG口已经损坏.此时请用万用表检查TCK,TMS,TDO和Tdi是否和GND短路,如果任何一个信号对地短路则表示JTAG信号管脚已经损坏.原因分析:我们经常为了方便,随意插拔JTAG下载口,在多数情况下不会发生任何问题.仍然有很小的概率因为热插拔而产…